
Waste services for industry
How Cardboard Balers Work
A baler compresses loose board in a steel chamber and holds it in shape with ties. What changes between machines is how material is fed, how big the bale is and what it takes to move it.
How a cardboard baler works
A cardboard baler works by pressing loose board inside a steel chamber, reducing the space it occupies, then holding the compressed material in shape with wire or plastic ties. On a typical vertical baler, cardboard is loaded through the feed opening, the loading door is closed and a hydraulic ram drives a platen into the chamber. The board folds and collapses under pressure, and the ram retracts ready for another load. This is repeated until there is enough material to form a bale. Horizontal balers use the same principle of compression, but their feeding and discharge arrangements differ.
When the bale is ready, it is secured with ties before the compression holding it together is released. On many vertical machines, ties are passed through channels in the chamber and around the compressed block, then secured by hand. Larger horizontal machines may have automatic tying equipment. The finished bale is then ejected or discharged using the arrangement fitted to that machine. Corrugated board tends to expand when pressure is released, so the ties hold the material together during storage and handling.
The reason sites bale at all is density. Loose cardboard contains a lot of air, so a cage or open container can fill long before it holds much fibre. Compressing the same material into tied bales reduces the storage space it occupies and can make collection and transport more efficient.

Vertical and horizontal machines
Vertical balers are generally loaded by hand at the front and run as a batch. The operator feeds board in, closes the loading door, operates the machine and repeats until there is enough material for a bale. The footprint is often smaller than that of a horizontal machine, but the installation still needs suitable headroom and space for doors and bale ejection. The amount of material loaded and compressed affects the finished bale weight.
Horizontal balers are fed through a hopper or a conveyor and compress along the length of a chamber rather than downwards. They suit higher and more continuous throughput, take more floor space, and on larger machines the tying step is carried out automatically rather than by hand. Layout, loading height, power and the way bales are discharged all vary by model, so the specification has to be matched to the building and to how the bales will be collected rather than assumed.
Between those two types the practical question is rarely which machine is better. It is whether the cardboard arrives in a steady flow that a continuously fed machine can use, or in bursts around deliveries and unpacking that a batch machine handles just as well.
What a mill size bale means
Mill size is a term the trade uses for larger, denser bales produced for mechanical handling and bulk transport to a paper mill. It is not a single legal standard. Bale dimensions, density and weight depend on the machine, the board going into it and the specification the receiving reprocessor works to, so the sensible order is to confirm what the outlet will accept first and choose the machine second.
The practical consequence is handling. Whether a bale can be moved with suitable pallet handling equipment or needs a forklift depends on its weight, dimensions and how it is presented for lifting. That needs settling before the baler is positioned. A machine that fits the room but produces bales nobody on site can move with the available equipment is the wrong machine for that room.
What changes the weight of a bale
Two bales from the same machine can differ noticeably, and the usual reasons are mechanical or related to the material being compressed:
- The board itself. Heavy double wall cases, light single wall cartons and mixed paperboard all behave differently under pressure.
- Moisture. Damp board is heavier, loses strength and may be downgraded or refused by a receiving mill, depending on the outlet specification.
- How the chamber is filled. Boxes dropped in whole can leave voids, while flattened board often allows a more consistent bale to form.
- The number of compression strokes before tying, and the pressure the machine develops.
- Chamber dimensions, which influence the outside size of the bale.
- The tying arrangement, which affects how well the compressed material retains its shape after pressure is released.
Bale weight matters in three places: whether the available handling equipment can move it, whether it can be stored securely, and whether the collection vehicle and the receiving site can take it. Consistent bales are easier to arrange for storage and loading than a mixture of different sizes and weights.

Power, space and the route the bales take
Before a machine is ordered, the measurements worth taking are the footprint, the clearance the door needs to open, the height required for the machine and whatever runs above that point in the building. The dimensions of the machine in its operating position matter, not just its width and depth on a specification sheet. Floor loading matters as well, both for the machine and for the bales that will stand beside it.
Check the electrical supply rather than assume it. Machines differ in whether they run from a standard single phase circuit or need a three phase supply, and an existing supply in the right place is not always enough for the load. Position is the other half of the question: the baler needs to sit where the cardboard can be brought to it, and the finished bales need a clear route to where they are stored and loaded, wide enough and flat enough for whatever moves them.
What belongs in the bale, and what does not
Baled cardboard is judged on what is inside the bale, not on what the outside looks like. Clean, dry corrugated and kraft board is generally suitable for a cardboard recycling stream. Stretch film, strapping, polystyrene, food residue, wet board and some coated or laminated packaging can affect acceptance by the receiving reprocessor. Excessive tape and other non-paper packaging components may also cause problems, depending on the outlet specification. Plastic film is particularly troublesome because it can interfere with paper reprocessing equipment.
If a site bales film as well as board, keep the feed areas and the finished bales apart so the two streams do not merge by accident. Packaging contaminated with oil, chemicals or food needs to be assessed separately rather than put into a clean cardboard bale. Our industrial recycling page explains how different material streams can be separated for recovery.
Keeping a baler available
A baler is work equipment, so the Provision and Use of Work Equipment Regulations 1998 (PUWER) apply to it. The equipment must be suitable for its intended use, maintained in a safe condition and used by people who have received adequate information, instruction and training. Appropriate protective measures are also required. The Health and Safety Executive explains that a significant proportion of serious and sometimes fatal accidents in waste and recycling involve poorly guarded machinery or improper use, including unsafe intervention when clearing blockages. Its guidance on machinery safety in waste and recycling covers these requirements.
Availability is another consideration. Hydraulic, electrical and tying faults can stop a baler, and cardboard does not stop arriving while it is out of service. Before installation, establish who deals with faults, what maintenance arrangements apply, which replacement parts may be needed and where loose board can be stored if the machine is unavailable.
Checks before choosing a machine
- Measure how much cardboard the site actually produces across a representative period, including the weeks when deliveries peak.
- Decide where the machine will stand, and walk the route the bales will take from the chamber to the collection point.
- Confirm the bale specification the receiving outlet works to before fixing on a machine size.
- Check the power supply, floor loading, headroom and operating clearances at the chosen position.
- Decide who will operate the machine, secure and eject finished bales, and move them to storage.
- Establish maintenance, replacement parts and fault response arrangements before the equipment is installed.
How baling changes collections
Once a site bales, the collection pattern follows bale accumulation rather than how quickly an open container looks full. Bales need somewhere dry to wait, with storage arranged so they do not obstruct working areas, vehicle movements or exits. The collection schedule depends on how quickly finished bales accumulate, the available storage space and the receiving outlet’s requirements. Clean, consistent bales can allow more cardboard to be moved in each load.
The paperwork for waste leaving the site is a separate consideration from how the baler operates. The waste duty of care code of practice explains the relevant responsibilities in England and Wales.
We can help with the equipment and collection side together. Our cardboard balers page covers hire, bale handling and rebate terms, while cardboard waste collection explains collection arrangements for loose, compacted and baled cardboard. Where the waste is mixed rather than clean board, waste compactor hire covers a different type of equipment. For storage and distribution sites, warehousing and logistics looks at cardboard alongside pallets, film and other packaging waste.
Free online tool
Waste Duty of Care Checker
Review common waste paperwork and collection questions relevant to your site.
Common questions
Frequently asked questions
How does a cardboard baler work?
A cardboard baler uses a hydraulic ram and platen to compress loose board inside a chamber. On a typical vertical machine, the operator loads cardboard, closes the loading door and operates the compression cycle until enough material has accumulated. The compressed board is secured with wire or plastic ties, then the finished bale is ejected. Horizontal machines use the same compression principle but can have different feeding, tying and discharge systems.
What is the difference between a vertical and a horizontal baler?
A vertical baler is generally hand loaded at the front and compresses downwards in batches, which suits moderate volumes and a limited footprint. A horizontal baler is fed through a hopper or conveyor and compresses along a chamber, which suits higher and more continuous throughput but needs more floor space.
What is a mill size bale?
It is the trade term for larger, denser bales made for mechanical handling and bulk transport to a paper mill. There is no single legal size. Dimensions and weight depend on the machine, the board and the specification the receiving reprocessor accepts, so the outlet specification should be confirmed before a machine is chosen.
What makes one bale heavier than another?
Board grade, moisture, how evenly the chamber was filled, the number of compression strokes, the pressure applied and the chamber dimensions all affect the finished weight. Boxes dropped in whole can leave voids, while flattened board often allows the machine to produce a more consistent bale. The tying arrangement affects how well the bale holds its shape after compression.
What power supply does a baler need?
That depends on the machine. Some run from a standard single phase circuit and others need a three phase supply, so the requirement should be checked against the supply available at the position where the machine will stand. Floor loading, operating clearances and headroom are worth measuring at the same time.
Can plastic film be baled with cardboard?
Plastic film should be kept out of cardboard bales because it can contaminate the recovered fibre and interfere with reprocessing equipment. Where a site generates both cardboard and film, keep the materials and finished bales separate. Some balers can handle different materials in separate batches, but the machine's suitability and the receiving outlet's specifications need to be checked.
Request a quote
Complete the form and we will get back to you.